Download  Print this page

Husqvarna 326RJ Operator's Manual

Husqvarna grass trimmer operator's manual.
Hide thumbs

Advertisement

Oper ator's manual (EPA)
326RJ
X-series
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Related Manuals for Husqvarna 326RJ

   Summary of Contents for Husqvarna 326RJ

  • Page 1

    Oper ator’s manual (EPA) 326RJ X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    15 metres from the machine. Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Only intended for trimmer heads.

  • Page 3: Table Of Contents

    Cutting equipment ... ASSEMBLY Fitting the J-handle ... Assembling the cutting equipment ... Fitting a trimmer guard and Superauto II 1" trimmer head ... Fitting the blade guard/combination guard, grass blade and grass cutter ... Fitting other guards and cutting attachments ...

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    What is what on the trimmer? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lockout 10 Cylinder cover 11 Starter handle...

  • Page 6: General Safety Precautions

    English Personal protective equipment IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby.

  • Page 8

    GENERAL SAFETY PRECAUTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

  • Page 9: Cutting Equipment

    WARNING! Using an incorrect cutting attachment or an incorrectly sharpened blade increases the risk of blade thrust. Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. – 9 English...

  • Page 10: Sharpening Grass Cutters And Grass Blades

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 11: Assembly

    Fitting a trimmer guard and Superauto II 1" trimmer head • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). •...

  • Page 12: Fitting The Blade Guard/combination Guard, Grass Blade And Grass Cutter

    (Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

  • Page 13: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two stroke-engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

  • Page 14: Fueling

    Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. •...

  • Page 15: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.

  • Page 16

    STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged.

  • Page 17: Working Techniques

    General working instructions IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.

  • Page 18: Grass Trimming With A Trimmer Head

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 19

    Sweeping • The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro. • When cutting and sweeping you should use full throttle to obtain the best results.

  • Page 20: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...

  • Page 21: Muffler

    will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. WARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop.

  • Page 22: Cooling System

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 23: Bevel Gear

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 24: Maintenance Schedule

    Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly.

  • Page 25: Technical Data

    Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. Approved accessories Arbor shaft thread M10 Plastic blades Grass blade/grass cutter Trimmer head TECHNICAL DATA 326RJX 1,50/24,5 1,34/34,0 1,06/27...

  • Page 26: Federal And California Emissions Control Warranty Statement

    FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Jonsered are pleased to explain the emissions control system’s warranty on your 2007 and later small off-road engine.

  • Page 27

    FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT HOW TO FILE A CLAIM If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden +46-36-146500. WHERE TO GET WARRANTY SERVICE Warranty services or repairs are provided through all Jonsered authorized servicing dealers.

  • Page 28

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...

  • Page 30

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...

  • Page 31

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m ~ 3,5 m 12 cm 5" “Click”...

  • Page 32

    Trimmy Hit Pro 15 cm 6" “Click” 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...

  • Page 33

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 34

    ´®z+RN[¶5,¨ ´®z+RN[¶5,¨ 4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 35

    T35, T35x 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 36

    1150465-95 ´®z+RN[¶5,¨ ´®z+RN[¶5,¨ 2007-01-09...

Comments to this Manuals

Symbols: 0
Latest comments: