Download  Print this page

Husqvarna 326L Operator's Manual

Husqvarna brush cutter operator's manual.
Hide thumbs

Advertisement

Operator's manual (EPA)
326C 326L 326L
X-SERIES
326LD
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Summary of Contents for Husqvarna 326L

  • Page 1

    Operator’s manual (EPA) 326C 326L 326L X-SERIES 326LD X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Only intended for trimmer heads.

  • Page 3: Table Of Contents

    YOUR WARRANTY RIGHTS AND OBLIGATIONS ... 24 CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! Whenever you use a clearing saw, brushcutter or trimmer you must wear personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate the risk of accidents, but it can reduce the effects of an injury in the event of an accident.

  • Page 5: Cutting Equipment

    fire. Never start the machine indoors or near combustible material! Cutting equipment A trimmer head is intended for trimming grass. Locking nut A locking nut is used to secure some types of cutting attachment.

  • Page 6: Checking, Maintaining And Servicing The Machine S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine s safety equipment. If your machine fails any of the checks described below you must contact your service agent.

  • Page 7: Cutting Equipment

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 8: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

  • Page 9: General Working Instructions

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 10

    SAFETY INSTRUCTIONS Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

  • Page 11: What Is What

    What is what? 1 Trimmer head 2 Grease filler cap 3 Bevel gear 4 Cutting attachment guard 5 Shaft7 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank...

  • Page 12: Assembly

    fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • 326L: Fit the nut, washer and screw. 326LX/326LDX: Fit the nut, knob and screw. Do not overtighten. •...

  • Page 13: Fitting A Trimmer Guard And Superauto Ii Trimmer Head

    (Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

  • Page 14: Fuel Handling

    14 – English FUEL HANDLING Two-stroke oil • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%). • Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

  • Page 15: Fuelling

    Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

  • Page 16: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.

  • Page 17

    STARTING AND STOPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Stopping Stop the engine by switching off the ignition. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.

  • Page 18: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after...

  • Page 19: Muffler

    will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. WARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop.

  • Page 20: Cooling System

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 21: Maintenance Schedule

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 22: Technical Data

    NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 22 – English TECHNICAL DATA 326C 326L 1,50/24,5 1,50/24,5 1,34/34,0 1,34/34,0 1,06/27...

  • Page 23

    Approved accessories 326C Blade shaft thread 3/8 R Plastic blades Trimmer head 326L, 326Lx, 326LDx Blade shaft thread M10 Plastic blades Trimmer head Attachments Clean sweep attachment with shaft Hedge trimmer attachment with shaft Edger attachment with shaft Saw attachment with shaft...

  • Page 24: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

  • Page 25

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...

  • Page 27

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...

  • Page 28

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m ~ 3,5 m 12 cm 5" “Click”...

  • Page 29

    Trimmy Hit Junior 15 cm 6" “Click” 5,75 m ~ 2,8 m 15 cm 6" 15 cm 6"...

  • Page 30

    Trimmy Hit Pro 15 cm 6" “Click” 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...

  • Page 31

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 32

    4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 33

    15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 34

    Trimmy VII ~ 15 cm 6" ´®z+H6e¶5/¨ ´®z+H6e¶5/¨ 15 cm 6" 7,0 m 23" 12 cm 5" ~ 3,5 m 11"...

  • Page 36

    1140226-95 ´®z+H6e¶5/¨ ´®z+H6e¶5/¨ 2003-09-17...

Comments to this Manuals

Symbols: 0
Latest comments: