Download  Print this page

Husqvarna 326HD60X-Series, 326HD75X-Series Operator's Manual

Husqvarna hedge trimmer operator's manual.
Hide thumbs

Advertisement

326HD60
326HD75
Please read the operator's manual carefully and make sure you understand the instructions
Operator's manual
X-series
X-series
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

   Related Manuals for Husqvarna 326HD60X-Series, 326HD75X-Series

   Summary of Contents for Husqvarna 326HD60X-Series, 326HD75X-Series

  • Page 1

    Operator′s manual 326HD60 326HD75 Please read the operator’s manual carefully and make sure you understand the instructions X-series X-series before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 3: Table Of Contents

    WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 4: Introduction

    Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.

  • Page 5: What Is What

    What is what? Operator′s manual Grease filler cap, bevel gear Gear housing Blades Blade guard Front handle Cylinder cover Starter handle Stop switch 10 Throttle lock 11 Adjustable handle 12 Throttle control WHAT IS WHAT? 13 Lock for handle 14 Fuel tank 15 Fuel cap 16 Air purge 17 Choke control...

  • Page 6: General Safety Precautions

    6 – English Personal protective equipment IMPORTANT! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 7: Machine's Safety Equipment

    See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted.

  • Page 8

    GENERAL SAFETY PRECAUTIONS Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Hand guard The hand guard prevents hands from coming into contact with the moving blades, for example, if the operator loses grip on the front handle.

  • Page 9

    GENERAL SAFETY PRECAUTIONS Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.

  • Page 10: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

  • Page 11: Fuelling

    Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

  • Page 12: Starting And Stopping

    Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight.

  • Page 13: Warm Engine

    Warm engine Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.

  • Page 14: Working Techniques

    General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

  • Page 15: Basic Working Techniques

    Do not rush the work, but work steadily until all the branches have been cut back cleanly. • The hedge trimmer’s rear handle can be set in three positions by pulling out the catch. See figure. When the handle is adjusted the hedge trimmer should be idling or not running.

  • Page 16: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust...

  • Page 17

    Low speed jet L Try to find the highest idle speed by turning the low speed jet L clockwise then anti-clockwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise. CAUTION! If the blades move while the engine is idling the T screw should be turned anti-clockwise until they stop.

  • Page 18: Muffler

    Correctly adjusted carburettor When the carburettor is correctly adjusted the machine accelerates without hesitation and burbles a little at maximum speed. It is also important that the blades do not move when the engine is idling or when the choke control is in the start position.

  • Page 19: Spark Plug

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 20: Gear Housing

    Use a grease gun to fill with grease. This should be done after every 60 working hours. Use Husqvarna’s special grease, no. 503 98 96-01. CAUTION! The gear housing must not be filled completely with grease. The grease expands as the machine heats up during operation.

  • Page 21: Maintenance Schedule

    Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual.

  • Page 22: Technical Data

    Technical data Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. fast idle speed, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm Fuel and lubrication system...

  • Page 28

    1151110-26 ´®z+S+"¶66¨ ´®z+S+"¶66¨ 2008-03-11...

Comments to this Manuals

Symbols: 0
Latest comments: