Download  Print this page

Husqvarna 325RJ Operator's Manual

Husqvarna gas hedge trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual (EPA)
323RJ 325RJ
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Related Manuals for Husqvarna 325RJ

   Summary of Contents for Husqvarna 325RJ

  • Page 1

    Operator’s manual (EPA) 323RJ 325RJ X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Only intended for trimmer heads.

  • Page 3: Table Of Contents

    YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment WARNING! Whenever you use a clearing saw, brushcutter or trimmer you must wear personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate the risk of accidents, but it can reduce the effects of an injury in the event of an accident.

  • Page 5: Cutting Equipment

    fire. Never start the machine indoors or near combustible material! Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. Locking nut A locking nut is used to secure some types of cutting attachment. – 5...

  • Page 6: Checking, Maintaining And Servicing The Machine S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine s safety equipment. If your machine fails any of the checks described below you must contact your service agent.

  • Page 7

    SAFETY INSTRUCTIONS Muffler • Never use a machine that has a faulty muffler. • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage.

  • Page 8: Cutting Equipment

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 9: Fuel Safety

    SAFETY INSTRUCTIONS Starting WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. • The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

  • Page 10: General Working Instructions

    • Use a grass cutter or grass blade for clearing grass. • Use a trimmer head or plastic blades for lighter clearing work, for example along verges or around trees. WARNING! Sometimes branches or grass get caught between the guard and cutting attachment.

  • Page 11

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 12: What Is What

    What is what on the trimmer? 1 Trimmer head 2 Grease filler cap 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle...

  • Page 13: Assembly

    (left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

  • Page 14: Fitting The Blade Guard/combination Guard, Grass Blade And Grass Cutter

    English ASSEMBLY Fitting other guards and cutting attachments • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). • Fit the drive disc (B) on the output shaft.

  • Page 15: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%). • Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

  • Page 16: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.

  • Page 17

    STARTING AND STOPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Stopping Stop the engine by switching off the ignition. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.

  • Page 18: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...

  • Page 19: Muffler

    will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop.

  • Page 20: Cooling System

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 503 47 73-01. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 21: Bevel Gear

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 22: Technical Data

    Tricut Ø 300 mm Grass 255-4 1" (Ø 255 4-teeth) Grass 255-8 1" (Ø 250 8-teeth) Trimmy H II 1" Trimmy Fix Trimmy Hit 1" Trimmy Hit Pro Superauto II 1" 325RJ-X 1,50/24,5 1,34/34 1,06/27 2700 11000-11700 8014 0,9/9000 WalbroMB/SEM AM49...

  • Page 23: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

  • Page 24

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6,5 ' 15 cm 6 " 6 "...

  • Page 25

    Tri Cut <20mm >20mm 6 Nm X 10...

  • Page 26

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...

  • Page 27

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m 12 cm 5" ~ 3,5 m “Click”...

  • Page 28

    Trimmy Hit Pro 15 cm 6" “Click” 15 cm 6" 7,5 m 15 cm 6" ~ 3,7 m...

  • Page 29

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 30

    ´®z+H0=¶5V¨ ´®z+H0=¶5V¨ 4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 31

    15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 32

    1140162-95 ´®z+H0=¶5V¨ ´®z+H0=¶5V¨ 2003-01-27...

  • Page 33

    FEDERAL EMISSION CONTROL WARRANTY STATEMENT – 33 English...

Comments to this Manuals

Symbols: 0
Latest comments: