Download Print this page

Husqvarna 324L Operator's Manual

Husqvarna grass trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual
324L
324LD
X-series
X-series
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Summary of Contents for Husqvarna 324L

  • Page 1

    Operator’s manual 324L 324LD X-series X-series Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Other symbols/decals on the machine refer to special certification requirements for certain markets.

  • Page 3: Table Of Contents

    YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

  • Page 5: Cutting Equipment

    fire. Never start the machine indoors or near combustible material! Cutting equipment A trimmer head is intended for trimming grass. Locking nut A locking nut is used to secure some types of cutting attachment.

  • Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′ ′ ′ ′ s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine ′ s safety equipment. If your machine fails any of the checks described below you must contact your service agent.

  • Page 7: Cutting Equipment

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 8: General Safety Precautions

    SAFETY INSTRUCTIONS WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

  • Page 9: General Working Instructions

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 10

    SAFETY INSTRUCTIONS Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

  • Page 11: What Is What

    What is what? 1 Trimmer head 2 Bevel gear 3 Grease filler cap, bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Stop switch 8 Throttle control 9 Throttle lock 10 Cylinder cover 11 Starter handle WHAT IS WHAT?

  • Page 12: Assembly

    Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft...

  • Page 13: Fitting The Trimmer Head

    (Caution! left-hand thread). ASSEMBLY • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. •...

  • Page 14: Fuel Handling

    When the machine is new the engine oil should be changed after the first month or after 10 hours of operation. • For the best result and function use HUSQVARNA engin oil. • When HUSQVARNA engine oil is not available another high grade engine oil can be used.

  • Page 15: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.

  • Page 16

    STARTING AND STOPPING Starting WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!).

  • Page 17: Maintenance

    Carburetor WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Function • The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. •...

  • Page 18: Spark Plug

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 19: Maintenance Schedule

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...

  • Page 20: Technical Data

    Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug...

  • Page 21

    Plastic blades Trimmer head Attachments Clean sweep attachment with shaft SR600 Hedge trimmer attachment with shaft HA 110 Hedge trimmer attachment with shaft HA 850 Edger attachment with shaft Saw attachment with shaft PA 1100 Saw attachment without shaft PA...

  • Page 22: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

  • Page 23: Super Auto Ii Assembly

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...

  • Page 25

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 26

    ´®z+H?[¶5ƨ ´®z+H?[¶5ƨ 4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 27: T35 Assembly

    15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 28

    1140315-95 ´®z+H?[¶5ƨ ´®z+H?[¶5ƨ 2004-09-09...

This manual also for:

324ld, 324lx series, 324ldx series

Comments to this Manuals

Symbols: 0
Latest comments: