Download  Print this page

Husqvarna 322 L Operator's Manual

Husqvarna gas hedge trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual (EPA II)
322L 323L 325C 325C
X-SERIES
325L
325L
325LD
X-SERIES
XT-SERIES
X-SERIES
Please read these instructions carefully and make
English
sure you understand them before using the machine.

Advertisement

   Also See for Husqvarna 322 L

   Related Manuals for Husqvarna 322 L

   Summary of Contents for Husqvarna 322 L

  • Page 1

    Operator's manual (EPA II) 322L 323L 325C 325C X-SERIES 325L 325L 325LD X-SERIES XT-SERIES X-SERIES Please read these instructions carefully and make English sure you understand them before using the machine.

  • Page 2: Symbol Explanation

    – English Always wear approved protective gloves. Use anti-slip and stable boots. Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. Only intended for the trimmer head. Other symbols/decals on the machine refer to special certification requirements for certain markets.

  • Page 3: Table Of Contents

    Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment MPORTANT INFORMATION • A clearing saw, brushcutter or trimmer used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.

  • Page 5: Cutting Equipment

    • are hot and can contain sparks that can cause fires. Never start the machine indoors or close to inflammable material. 6. Cutting equipment The trimmer head is intended for trimming grass. 7. Locking nut A locking nut is used to...

  • Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment

    Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.

  • Page 7: Cutting Equipment

    • Make sure the knife positioned on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a few days.

  • Page 8: General Safety Instructions

    General safety instructions IMPORTANT INFORMATION • The machine is only designed for trimming grass. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •...

  • Page 9: General Working Instructions

    General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the trimmer. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

  • Page 10

    – English SAFETY INSTRUCTIONS Trimming • The trimmer is ideal to cut grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting.

  • Page 11: What Is What

    What is what on the trimmer? 1. Trimmer head 2. Grease filler cap 3. Angle gear 4. Spray guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13.

  • Page 12: Assembly

    • 322L/323L: Fit the nut, washer and bolt. 325L /325L /325LD Fit the nut, knob and bolt. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. – English ASSEMBLY Assembling and dismantling the...

  • Page 13: Assembling The Spray Guard And Trimmer Head Superauto

    • Insert the locking pin (C) in the hole so that the axle is locked. • The trimmer head must be split to be fitted (see the diagram). Proceed as follows: • Insert your finger into the...

  • Page 14: Fitting The Spray Guard And Trimmer Head

    Fitting the spray guard and trimmer head (325C • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the axle. • Screw the trimmer head onto the shaft. Tighten securely.

  • Page 15: Fuel Handling

    • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two- stroke oil, which has been specially developed for clearing saws and chain saws. Mixing ratio 1:50 (2%).

  • Page 16: Start And Stop

    1.5 Nm. The tightening torque of the locking nut should be 35-50 Nm. • Check that the trimmer head and spray guard are not damaged or cracked. Replace the trimmer head or spray guard if they are exposed to impact or are cracked.

  • Page 17: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and...

  • Page 18

    Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clock- wise until the cutting attachment stops.

  • Page 19: Muffler

    Muffler NOTE! Some mufflers are fitted with a catalytic converter. See “Technical data” to see whether your machine is fitted with a catalytic converter. The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user. The exhaust fumes are hot and can contain sparks, which can result in fire if the...

  • Page 20: Air Filter

    – English MAINTENANCE NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.

  • Page 21: Technical Data 322l/323l

    Technical data Engine Displacement, cu. in/cm Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm...

  • Page 22

    Technical data Engine Displacement, cu. in/cm Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893 kW/rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm...

  • Page 23: 325ldx

    Trimmy HII 1" Trimmy Hit Trimmy Hit Pro Superauto II 1" Attachments Clean sweep attachment with shaft Hedge trimmer attachment with shaft Edger with attachment shaft Saw attachment with shaft Saw attachment without shaft TECHNICAL DATA Cutting attachment guard Art No.

  • Page 24: Emission Control Warranty Statement

    As the small nonroad engine owner, you should, however, be aware that Husqvarna Forest & Garden may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.

  • Page 25

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 " English –...

  • Page 26

    Tri Cut >20mm >20mm 6 Nm X 10 – English...

  • Page 27

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" English –...

  • Page 28

    Trimmy Hit “Click” ~ 15 cm " – English 15 cm 6 " 7,0 m ~ 3,5 m 12 cm 5" “Click”...

  • Page 29

    Trimmy Hit Junior 15 cm 6" “Click” 15 cm 6" 5,75 m 15 cm 6" ~ 2,8 m English –...

  • Page 30

    Trimmy Hit Pro 15 cm 6" “Click” – English 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...

  • Page 31

    Trimmy Hit VI ~ 15 cm " 15 cm " 7,0 m 12 cm 5" ~ 3,5 m “Click” English –...

  • Page 32

    Trimmy SII 7,0 m 12 cm 5" ~ 3,5 m ~ 15 cm "Clic" 35-50 NM – English...

  • Page 33

    English –...

  • Page 34

    Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6" ´+H)y¶5h¨ – English...

  • Page 35

    English –...

  • Page 36

    114 00 98-95 ´+H)y¶5h¨ 2002W11...

Comments to this Manuals

Symbols: 0
Latest comments: