Download  Print this page

Husqvarna Viking CA 150 Operator's Manual

Cultivator attachment.
Hide thumbs

Advertisement

Operator ' s manual Manuel d'utilisation
Manual de instrucciones
Cultivator attachment CA 150
Accessoire de cultivateur CA 150
Accesorio de cultivador CA 150
.
G G G G B B B B F F F F R R R R E E E E S S S S

Advertisement

   Summary of Contents for Husqvarna Viking CA 150

  • Page 1

    Operator ′ s manual Manuel d’utilisation Manual de instrucciones Cultivator attachment CA 150 Accessoire de cultivateur CA 150 Accesorio de cultivador CA 150 G G G G B B B B F F F F R R R R E E E E S S S S...

  • Page 2: Key To Symbols

    Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •...

  • Page 3: Table Of Contents

    Technical data ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

  • Page 5: General Safety Precautions

    SAFETY INSTRUCTIONS WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

  • Page 6: General Working Instructions

    (i.e. without the resistance that the cutting attachment exerts on the engine when you are using the machine) can lead to serious engine damage. • Pay extra attention when pulling the cultivator towards you while working. • If heavy vibration occurs, stop the machine. Disconnect the HT lead from the spark plug.

  • Page 7: What Is What

    What is what on the cultivator attachment? 1 Blade guard 2 Shaft 3 Blades 4 Split pin WHAT IS WHAT? 5 Cotter pin 6 Grease filler cap, bevel gear 7 Bevel gear 8 Operator ′ s manual – 7 English...

  • Page 8: Assembly

    Fitting the bevel gear • Assembling the angle gear on the shaft. Turn the shaft so that the splines on the drive axle mate in the angle gear. • First tighten the screw H and then the screw M. Assembling the guard. •...

  • Page 9: Starting And Stopping

    STARTING AND STOPPING Check before starting For safety reasons follow these recommendations! • Inspect the working area. Remove any objects that could be thrown out. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. •...

  • Page 10: Maintenance

    However, before using the machine you should check that the bevel gear is filled three-quarters (40g) full with grease. Use HUSQVARNA special grease. CAUTION! The gear housing must not be filled completely with grease. The grease expands as the machine heats up during operation.

  • Page 11: Technical Data

    Technical data Technical data Weight Weight, Lbs/kg Blades Diameter tines, mm Working width, mm Tine speed at engine speed 10,500 r/min TECHNICAL DATA CA 150 – 11 English...

  • Page 12

    1150001-20 ´®z+RÆ,¶0n¨ ´®z+RÆ,¶0n¨ 2004-11-10...

This manual also for:

Ca 150

Comments to this Manuals

Symbols: 0
Latest comments: