Download Print this page

Advertisement

Operator's manual (CARB II, EPA II)
326C 326L 326L
X-SERIES
326LD
X-SERIES
Please read these instructions carefully and make
English
sure you understand them before using the machine.

Advertisement

   Also See for Husqvarna 326C, 326L, 326LX-Series, 326LDX-Series

   Related Manuals for Husqvarna 326C, 326L, 326LX-Series, 326LDX-Series

   Summary of Contents for Husqvarna 326C, 326L, 326LX-Series, 326LDX-Series

  • Page 1

    Operator's manual (CARB II, EPA II) 326C 326L 326L X-SERIES 326LD X-SERIES Please read these instructions carefully and make English sure you understand them before using the machine.

  • Page 2: Symbols

    SYMBOL EXPLANATION Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use •...

  • Page 3: Table Of Contents

    Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment MPORTANT INFORMATION • A clearing saw, brushcutter or trimmer used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.

  • Page 5: Cutting Equipment

    SAFETY INSTRUCTIONS 4. Vibration damping system Your machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. Use of incorrectly wound cord or incorrect cutting equipment increases the level of vibration. The machine’s vibration damping system reduces the transfer of vibrations...

  • Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment

    Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.

  • Page 7: Cutting Equipment

    SAFETY INSTRUCTIONS 6. Cutting equipment The section describes how through correct maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment. Two basic rules: 1)Only use the cutting and guard equipment we recommend! See...

  • Page 8: General Safety Instructions

    General safety instructions IMPORTANT INFORMATION • The machine is only designed for trimming grass. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •...

  • Page 9: Basic Working Techniques

    SAFETY INSTRUCTIONS General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the trimmer. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

  • Page 10: General Working Instructions

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.

  • Page 11: What Is What

    What is what on the trimmer? 1. Trimmer head 2. Grease filler cap 3. Angle gear 4. Spray guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13.

  • Page 12: Assembly

    Assembling the loop handlebar (326C) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Assembling the loop handlebar (326L, 326L , 326LD...

  • Page 13: Assembling The Spray Guard And Trimmer Head Superauto

    Assembling the spray guard and trimmer head Superauto II (326L, 326L , 326LD • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the drive disc (B) on the output axle.

  • Page 14: Fuel Handling

    • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for clearing saws and chain saws. Mixing ratio 1:50 (2%). • Never use two-stroke oil...

  • Page 15: Start And Stop

    Control before starting For reasons of safety follow these recommendations! • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force.

  • Page 16: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and...

  • Page 17

    Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clock- wise until the cutting attachment stops.

  • Page 18: Muffler

    Muffler NOTE! Some mufflers are fitted with a catalytic converter. See “Technical data” to see whether your machine is fitted with a catalytic converter. The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user.

  • Page 19: Air Filter

    MAINTENANCE NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does...

  • Page 20: Technical Data

    Technical data Engine Displacement, cu. in/cm Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel lubrication system...

  • Page 21: Emission Control Warranty Statement

    REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be perfor- med at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &...

  • Page 22

    Super Auto II Super Auto II 1 " 4,0 m – English 15 cm ~2,0 m 6,5 ' 15 cm 6 " 6 "...

  • Page 23

    Tri Cut >20mm >20mm 6 Nm X 10 English –...

  • Page 24

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" – English...

  • Page 25

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m 12 cm 5" ~ 3,5 m “Click” English –...

  • Page 26

    Trimmy Hit Junior 15 cm 6" “Click” – English 5,75 m ~ 2,8 m 15 cm 6" 15 cm 6"...

  • Page 27

    Trimmy Hit Pro 15 cm 6" “Click” 15 cm 6" 7,5 m 15 cm 6" ~ 3,7 m English –...

  • Page 28

    Trimmy Hit VI ~ 15 cm " – English 15 cm " 7,0 m 12 cm 5" ~ 3,5 m “Click”...

  • Page 29

    Trimmy SII ~ 15 cm 35-50 NM 7,0 m 12 cm 5" ~ 3,5 m "Clic" English –...

  • Page 30

    ´+H,=¶3C¨ – English...

  • Page 31

    Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6" English –...

  • Page 32

    114 01 22-93 ´+H,=¶3C¨ 2002W23...

Comments to this Manuals

Symbols: 0
Latest comments: