Download Print this page

Husqvarna 327LDX-series Operator's Manual

Husqvarna brush cutter/ trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual
327LD
X-series
Please read the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

   Also See for Husqvarna 327LDX-series

   Summary of Contents for Husqvarna 327LDX-series

  • Page 1

    Operator′s manual 327LD X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before...

  • Page 3: Table Of Contents

    Contents KEY TO SYMBOLS Symbols ... 2 CONTENTS Contents ... 3 Note the following before starting: ... 3 INTRODUCTION Dear Customer, ... 4 WHAT IS WHAT? What is what? ... 5 GENERAL SAFETY PRECAUTIONS Important ... 6 Personal protective equipment ... 6 Machine′s safety equipment ...

  • Page 4: Introduction

    Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.

  • Page 5: What Is What

    What is what? Trimmer head Grease filler cap, bevel gear Bevel gear Cutting attachment guard Shaft Shaft coupling Loop handle Throttle control Stop switch 10 Throttle lockout 11 Spark plug cap and spark plug WHAT IS WHAT? 12 Cylinder cover 13 Starter handle 14 Fuel tank 15 Air filter cover...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS BOOTS Wear sturdy, non-slip boots. CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level.

  • Page 8

    GENERAL SAFETY PRECAUTIONS Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.

  • Page 10: Assembly

    Fitting the loop handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. Fit the nut, knob and screw. Do not overtighten. •...

  • Page 11: Assembling The Cutting Equipment

    Assembling the cutting equipment WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

  • Page 12: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

  • Page 13: Fuelling

    Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

  • Page 14: Starting And Stopping

    Check before starting • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm.

  • Page 15

    STARTING AND STOPPING apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.

  • Page 16: Working Techniques

    General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.

  • Page 17: Basic Working Techniques

    Basic working techniques Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. WARNING! Sometimes branches or grass get caught between the guard and cutting attachment.

  • Page 18: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust...

  • Page 19

    Low speed jet L Try to find the highest idle speed by turning the low speed jet L clockwise then anti-clockwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise. CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

  • Page 20: Muffler

    Muffler CAUTION! Some mufflers are fitted with a catalytic converter. See chapter on Technical data to see whether your machine is fitted with a catalytic converter. The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

  • Page 21: Two-piece Shaft

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 22: Bevel Gear

    However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

  • Page 23: Maintenance Schedule

    Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual.

  • Page 24: Technical Data

    Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug...

  • Page 25: Ec-declaration Of Conformity

    Edger attachment with shaft Saw attachment with shaft PA 1100 Cultivator attachment with shaft CA 150 The following attachments have been developed mainly for the Husqvarna 125LD trimmer, but can also be used with the specified models. Approved accessories Cultivator attachment CAC...

  • Page 27

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 28

    4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 29

    T35, T35x 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 30

    15 cm 6" 6,0 m 10 cm 4" 3,05 m "Clic"...

  • Page 36

    1151209-26 ´®z+S4|¶6|¨ ´®z+S4|¶6|¨ 2009-09-18...

This manual also for:

327ls, 327ld, 327ldx series

Comments to this Manuals

Symbols: 0
Latest comments: