Download  Print this page

Husqvarna 326C, 326L, 326LS, 326LX-Series, 326LDX-Series Operator's Manual

Husqvarna string trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual (Carb II, EPA II)
326C 326L 326L
X-SERIES
326LD
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Also See for Husqvarna 326C, 326L, 326LS, 326LX-Series, 326LDX-Series

   Summary of Contents for Husqvarna 326C, 326L, 326LS, 326LX-Series, 326LDX-Series

  • Page 1

    Operator’s manual (Carb II, EPA II) 326C 326L 326L X-SERIES 326LD X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.

  • Page 2: Key To Symbols

    Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •...

  • Page 3: Table Of Contents

    Contents KEY TO SYMBOLS Symbols ... CONTENTS Contents ... Note the following before starting: ... INTRODUCTION Dear customer! ... WHAT IS WHAT? What is what? ... GENERAL SAFETY PRECAUTIONS Important ... Personal protective equipment ... Machine ′ s safety equipment ... Cutting equipment ...

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    What is what? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank WHAT IS WHAT? 13 Choke control 14 Air purge...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

  • Page 7

    GENERAL SAFETY PRECAUTIONS IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine ′ s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service.

  • Page 8

    GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. See instructions under the heading Cutting equipment.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Locking nut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates.

  • Page 10: Assembly

    Fitting the loop handle (326C) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut.

  • Page 11: Fitting The Trimmer Head

    Fitting the trimmer head WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury.

  • Page 12: Fitting The Trimmer Guard And Trimmer Head

    Fitting the trimmer guard and trimmer head (326C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. •...

  • Page 13: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%). • Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

  • Page 14: Fueling

    Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. •...

  • Page 15: Starting And Stopping

    STARTING AND STOPPING Check before starting WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately. • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.

  • Page 16

    STARTING AND STOPPING CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a machine with damaged spark plug cap.

  • Page 17: Working Techniques

    General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.

  • Page 18

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 19: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...

  • Page 20: Muffler

    Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.

  • Page 21: Cooling System

    Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the cylinder).

  • Page 22: Bevel Gear

    Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it.

  • Page 23: Maintenance Schedule

    Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.

  • Page 24: Technical Data

    Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug...

  • Page 25

    Approved accessories 326C Blade shaft thread 3/8 R Plastic blades Trimmer head 326L, 326Lx, 326LDx Arbor shaft thread M10 Plastic blades Trimmer head Attachments Clean sweep attachment with shaft SR600 Hedge trimmer attachment with shaft HA 110 Hedge trimmer attachment with shaft HA 850 Edger attachment with shaft Saw attachment with shaft PA 1100 Saw attachment without shaft PA...

  • Page 26: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

  • Page 27

    Trimmy Hit Junior 15 cm 6" “Click” 5,75 m ~ 2,8 m 15 cm 6" 15 cm 6"...

  • Page 28

    Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6"...

  • Page 29

    15 cm 6" 6,0 m 10 cm 4" 3,05 m "Clic"...

  • Page 30

    T25C 2,75 m 2,75 m 15 cm 6"...

  • Page 31

    T25C 15 cm 6" 2,75 m x 2 9' x 2 2,75 m 2,75 m "Clic"...

  • Page 32

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...

  • Page 33

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m ~ 3,5 m 12 cm 5" “Click”...

  • Page 34

    Trimmy Hit Pro 15 cm 6" “Click” 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...

  • Page 35

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...

  • Page 36

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 37

    4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 38

    ´®z+HAo¶5;¨ ´®z+HAo¶5;¨...

  • Page 39

    15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...

  • Page 40

    1140337-95 ´®z+HAo¶5;¨ ´®z+HAo¶5;¨ 2005-07-11...

This manual also for:

326ldx series326lx series

Comments to this Manuals

Symbols: 0
Latest comments:
  • Ben Apr 02, 2015 01:38:
    how do i disconnect shaft from motor husqvarna 326LX