Download  Print this page

Husqvarna 323R, 325RX-Series, 325RDX-Series Operator's Manual

Husqvarna trimmer operator's manual.
Hide thumbs

Advertisement

Operator's manual (EPA II)
323R 325R
X-SERIES
325R
325RD
XT-SERIES
X-SERIES
Please read these instructions carefully and make
English
sure you understand them before using the machine.

Advertisement

   Also See for Husqvarna 323R, 325RX-Series, 325RDX-Series

   Related Manuals for Husqvarna 323R, 325RX-Series, 325RDX-Series

   Summary of Contents for Husqvarna 323R, 325RX-Series, 325RDX-Series

  • Page 1

    Operator's manual (EPA II) 323R 325R X-SERIES 325R 325RD XT-SERIES X-SERIES Please read these instructions carefully and make English sure you understand them before using the machine.

  • Page 2: Symbol Explanation

    SYMBOL EXPLANATION Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use •...

  • Page 3: Table Of Contents

    Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.

  • Page 4: Safety Instructions

    Personal protective equipment IMPORTANT INFORMATION • Incorrect or careless use of a clearing saw, brushcutter or trimmer can turn it into a dangerous tool that can cause serious or even fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.

  • Page 5

    2. Stop switch The stop switch should be used to stop the engine. 3. Cutting attachment guard This guard is intended to prevent objects from being thrown towards the operator and to protect the operator from unintentionel contact with the cutting attachment. WARNING! Do not attach any blade to the unit without proper installation of all required...

  • Page 6

    6. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the operator. Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious.

  • Page 7: Control, Maintenance And Service Of The Machine's Safety Equipment

    Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.

  • Page 8

    3. Cutting attachment guard • Check that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data". 4.

  • Page 9: Cutting Equipment

    6. Cutting equipment This section describes how through correct maintenance and through using the right type of cutting equipment you can: • Reduce the machine‘s tendency to kickback • Obtain maximum cutting capacity. • Increase the service life of the cutting equipment. Four basic rules: 1)Only use the cutting and guard equipment...

  • Page 10: Cutting Equipment

    Cutting equipment IMPORTANT INFORMATION The section describes how through correct mainte- nance and through using the right type of cutting equipment you can reduce the machine‘s tendency to kickback, obtain maximum clearing capacity and increase the service life of the cutting equipment. •...

  • Page 11: General Safety Instructions

    General safety instructions IMPORTANT INFORMATION • This machine is intended solely for trimming and clearing grass and for light brush-cutting. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“...

  • Page 12: General Working Instructions

    General working instructions IMPORTANT INFORMATION • This section covers basic safety precautions for working with brushcutters and trimmers. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

  • Page 13: Basic Clearing Techniques

    Adjusting the harness and clearing saw WARNING! When working with the clearing saw it should always be hooked in the harness. If this is not done, you cannot control the clearing saw safely and this can result in injury to yourself or someone else. Never use a harness with a defective quick release catch.

  • Page 14

    Clearing‘s ABC Always use the correct equipment. Always have well adjusted equipment. Follow the safety instructions. Organise the work well. Always use full throttle when applying the blade. Always use a sharp blade. Avoid stones. WARNING! Avoid cutting in the cutting region between 12 and 3 o‘clock on the blade.

  • Page 15

    Grass clearing using the trimmer head and plastic blades. • Hold the trimmer head just above the ground at an angle. It is the end of the cord that carries out the work. Let the cord work at its own pace. Do not press the cord into the area to be cut.

  • Page 16: What Is What

    What is what on the brushcutter? 1. Blade 2. Grease filler cap 3. Angle gear 4. Combination guard 5. Shaft 6. Handlebars 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Hanging ring 11. Cylinder cover 12. Starter handle 13.

  • Page 17: Assembly

    Assembling the handlebars (323R) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars.

  • Page 18: Assembly Of The Blade And Trimmer Head

    Assembly of the blade and trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury.

  • Page 19: Assembling The Spray Guard And Trimmer Head

    Assembling the spray guard and trimmer head Superauto II • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the drive disc (B) on the output axle.

  • Page 20: Assembling And Dismantling The Two-part Shaft (325r Xt , 325rd X )

    Assembling and dismantling the two-part shaft (325R Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling‘s locking plate on the upper section of the shaft. The sections are then locked together.

  • Page 21: Fuel Handling

    • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two- stroke oil, which has been specially developed for clearing saws and chain saws. Mixing ratio 1:50 (2%).

  • Page 22: Start And Stop

    Control before starting For reasons of safety follow these recommendations! • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening...

  • Page 23

    For throttle handles with a start throttle lock: Set the throttle to the start position by first pressing the throttle lock and the throttle trigger, then pressing the start throttle button (A). Then release the throttle lock and the throttle trigger, followed by the start throttle button.

  • Page 24: Maintenance

    Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and producing the least amount of harmful...

  • Page 25

    Final setting of the idling speed T Adjust the idling speed with the screw T, If it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops.

  • Page 26: Muffler

    However, before using the machine you should check that the angle gear is filled to 3/4 with grease. Use HUSQVARNA special grease. Normally, the grease does not need to be changed except when the angle gear is repaired.

  • Page 27: Air Filter

    If the machine is used in dusty conditions the air filter should be soaked in oil, see the section on “Oiling the air filter“. Oiling the air filter Always use HUSQVARNA filter oil, order no. 503 47 73-01. The filter oil contains a solvent to make it spread evenly through the filter.

  • Page 28: Sharpening The Clearing Blade

    1 mm. – English MAINTENANCE NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.

  • Page 29: Technical Data

    Technical data Engine Displacement, cu. in/cm Cylinder bore, inch/mm Stroke length, inch/mm Idling speed, rpm Recommended max. speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893. kW/rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm...

  • Page 30: 325rdx

    Approved accessories 323R Centre hole in blades Ø 25,4 mm Threaded blade axle M10 Grass blade Saw blade Plastic knives Trimmer head Support cup Approved accessories 325R , 325R , 325RD Centre hole in blades Ø 25,4 mm Threaded blade axle M10 Grass blade Saw blade Plastic knives...

  • Page 31: Emission Control Warranty Statement

    As the small nonroad engine owner, you should, however, be aware that Husqvarna Forest & Garden may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.

  • Page 32

    Super Auto II Super Auto II 1 " 4,0 m – English 15 cm ~2,0 m 6,5 ' 15 cm 6 " 6 "...

  • Page 33

    Tri Cut >20mm >20mm 6 Nm X 10 English –...

  • Page 34

    Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" – English...

  • Page 35

    Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m 12 cm 5" ~ 3,5 m “Click” English –...

  • Page 36

    Trimmy Hit Junior 15 cm 6" “Click” – English 5,75 m ~ 2,8 m 15 cm 6" 15 cm 6"...

  • Page 37

    Trimmy Hit Pro 15 cm 6" “Click” 15 cm 6" 7,5 m 15 cm 6" ~ 3,7 m English –...

  • Page 38

    Trimmy Hit VI ~ 15 cm " – English 15 cm " 7,0 m 12 cm 5" ~ 3,5 m “Click”...

  • Page 39

    Trimmy SII 7,0 m 12 cm 5" ~ 3,5 m ~ 15 cm "Clic" 35-50 NM English –...

  • Page 40

    – English...

  • Page 41

    English –...

  • Page 42

    ´+H*G¶5q¨ – English...

  • Page 43

    English –...

  • Page 44

    114 01 03 -95 ´+H*G¶5q¨ 2002W13...

Comments to this Manuals

Symbols: 0
Latest comments: