Download  Print this page

Advertisement

Operator ' s manual
326R
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Also See for Husqvarna 326R X-SERIES

   Related Manuals for Husqvarna 326R X-SERIES

   Summary of Contents for Husqvarna 326R X-SERIES

  • Page 1

    Operator ′ s manual 326R X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specified in chapter WARNING! Careless or incorrect use can Technical data and on label. result in serious or fatal injury to the operator or others.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the Symbols ............... design and appearance of products without prior notice. CONTENTS Contents ..............

  • Page 4: Introduction

    Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    WHAT IS WHAT? What is what? 1 Blade 17 Handle adjustment 2 Grease filler cap, bevel gear 18 Locking nut 3 Bevel gear 19 Support flange 4 Cutting attachment guard 20 Support cup 5 Shaft 21 Drive disc 6 Handlebar 22 Trimmer head 7 Throttle control 23 Socket spanner...

  • Page 6: Safety Instructions

    SAFETY INSTRUCTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if The machine is only designed for trimming grass, grass used incorrectly or carelessly, and can cause serious or clearing and/or forestry clearing. fatal injury to the operator or others.

  • Page 7: Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS CLOTHING Make sure the throttle control is locked at the idle setting when the throttle lock is released. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants.

  • Page 8

    SAFETY INSTRUCTIONS Cutting attachment guard Quick release This guard is intended to prevent loose objects from being There is an easily accessible, quick release fitted at the front thrown towards the operator. The guard also protects the as a safety precaution in case the engine catches fire, or in operator from accidental contact with the cutting attachment.

  • Page 9: Cutting Equipment

    SAFETY INSTRUCTIONS Cutting equipment If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious This section describes how to choose and maintain your damage.

  • Page 10: Sharpening The Saw Blade

    SAFETY INSTRUCTIONS Sharpening grass cutters and grass General rules blades Only use cutting attachments with the guards we recommend! See the chapter on Technical data. • See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters using a single-cut flat file. •...

  • Page 11: Trimmer Head

    SAFETY INSTRUCTIONS Adjust the blade setting. This should be 1 mm. Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords.

  • Page 12: Assembly

    ASSEMBLY Fitting the handlebar • Now twist the handlebar around the shaft. Tighten the knob. • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the • Fit the transport guard to the cutting attachment. handlebar, (see diagram).

  • Page 13: Fitting The Blade Guard And Saw Blade

    ASSEMBLY • Turn the blade shaft until one of the holes in the drive disc • Place the blade (D) and support flange (F) on the output aligns with the corresponding hole in the gear housing. shaft. • Insert the locking pin (C) in the hole to lock the shaft. •...

  • Page 14: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head

    ASSEMBLY Fitting a trimmer guard and Fitting other guards and cutting Superauto II 1” trimmer head attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hook the guard onto the fitting on the shaft and secure it with the bolt (L).

  • Page 15: Adjusting The Harness And Clearing Saw

    ASSEMBLY Adjusting the harness and clearing Correct balance Let the cutting attachment rest lightly on the ground. If you use a saw blade it should balance about 10 cm above the ground to prevent contact with stones and the like. Adjust the WARNING! When using a clearing saw it position of the support hook to balance the clearing saw must always be hooked securely to the...

  • Page 16: Fuel Handling

    Mixture 1:50 (2%). • If HUSQVARNA two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines. Contact your dealer when selecting an oil.

  • Page 17: Fuelling

    FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

  • Page 18: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most WARNING! The complete clutch cover and common reason why cracks are formed is that sharp shaft must be fitted before the machine is corners have been formed at the bottom of the teeth while started, otherwise the clutch can come loose...

  • Page 19

    STARTING AND STOPPING Stopping CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Stop the engine by switching off the ignition. CAUTION! Do not put any part of your body in marked area.

  • Page 20: Working Techniques

    WORKING TECHNIQUES General working instructions 6 Never put the machine down with the engine running unless you have it in clear sight. The ABC of clearing IMPORTANT! This section describes the basic safety precautions for • Always use the correct equipment. working with clearing saws and trimmers.

  • Page 21

    WORKING TECHNIQUES • Start at whichever end of the area is easiest, and clear an • To fell to the right, the bottom of the tree should be pushed open space from which to work. to the left. Tilt the blade and bring it diagonally up to the right.

  • Page 22: Brush Cutting With A Saw Blade

    WORKING TECHNIQUES Brush cutting with a saw blade • Stop the engine, unclip the harness and place the machine on the ground before you start to collect the cut material. Grass trimming with a trimmer head • Thin stems and brush are mown down. Work with a sawing movement, swinging sideways.

  • Page 23

    WORKING TECHNIQUES • Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head. Sweeping • The fan effect of the rotating cord can be used for quick and easy clearing up.

  • Page 24: Maintenance

    CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful Rec. idle speed 2700 rpm emissions.

  • Page 25: Muffler

    MAINTENANCE will run smoothly in every position. The idle speed should also If the high speed jet H is set too lean it will result in less power, be well below the speed at which the cutting attachment starts less performance, poor acceleration and/or damage to the to rotate.

  • Page 26: Cooling System

    filled three-quarters full with grease. Use If the mesh is frequently blocked, this can be a sign that the HUSQVARNA special grease. performance of the catalytic converter is impaired. Contact your dealer to inspect the muffler. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston.

  • Page 27: Spark Plug

    Sharpen blades and cutters using a single-cut flat file. • Sharpen all edges equally to maintain the balance of the Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The blade. filter oil contains a solvent to make it spread evenly through the filter.

  • Page 28: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop.

  • Page 29: Technical Data

    TECHNICAL DATA Technical data Technical data 326Rx Engine Cylinder displacement, cm 24,5 Cylinder bore, mm 34,0 Stroke, mm Idle speed, rpm 2700 Recommended max. fast idle speed, rpm 11000-11700 Speed of output shaft, rpm 8000 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8400 Catalytic converter muffler Speed-regulated ignition system...

  • Page 30: Ec-declaration Of Conformity

    (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saw Husqvarna 326R-X with serial numbers dating from 2002 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...

  • Page 31

    Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...

  • Page 33

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 34

    4,25 m 4,25 m 15 cm 6" 15 cm 6" ´®z+HA"¶6x¨ ´®z+HA"¶6x¨...

  • Page 35

    8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...

  • Page 36

    1140330-26 ´®z+HA"¶6x¨ ´®z+HA"¶6x¨ 2004-10-07...

Comments to this Manuals

Symbols: 0
Latest comments: