Download Print this page

Advertisement

Oper ator's manual (EPA)
223L
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

   Related Manuals for HUSQVARNA 223L

   Summary of Contents for HUSQVARNA 223L

  • Page 1

    Oper ator’s manual (EPA) 223L Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY T O SYMBOLS Symbols WARNING! Clearing saws, brushcutters and Only intended f or trimmer heads. trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the f ollowing before starting: KEY TO SYMBOLS Please read the oper ator’s manual carefully. Symbols ............... Long-term exposure to noise can result in permanent hearing CONTENTS impairment. So always use approved hearing protection. Contents ..............Maintenance, replacement, or repair of the emission control Note the following before starting: ........

  • Page 4: Intr Oduction

    Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    WHA T IS WHA T? What is what? 1 Trimmer head 12 Fuel tank 2 Grease filler cap, bevel gear 13 Choke control 3 Bevel gear 14 Air purge 4 Cutting attachment guard 15 Air filter cover 5 Shaft 16 Handle adjustment 6 Loop handle 17 Drive disc 7 Throttle control...

  • Page 6: General Safety Preca Utions

    GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment IMPORTANT! IMPOR TANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or The only accessories you can operate with this engine unit fatal injury to the operator or others.

  • Page 7: Mac Hine's Safety Equipment

    GENERAL SAFETY PRECA UTIONS FIRST AID KIT Make sure the throttle control is locked at the idle setting when the throttle lock is released. Alw ays have a first aid kit nearby. Press the throttle lock and make sure it returns to its original Mac hine′s safety equipment position when you release it.

  • Page 8

    GENERAL SAFETY PRECAUTIONS Cutting attachment guard Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is undamaged and securely attached. WARNING! Overexposure to vibration can This guard is intended to prevent loose objects from being lead to circulatory damage or nerve damage thrown towards the operator.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Cutting equipment If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious This section describes how to choose and maintain your damage.

  • Page 10: Assembly

    ASSEMBLY Fitting the loop handle Fitting the trimmer guard and trimmer head • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the correct trimmer guard (A) for use with the trimmer head.

  • Page 11: Fuel Handling

    • In order to prevent unintentional starting of the engine, the • For best results and performance use HUSQVARNA two- spark plug cap must always be removed during long-term stroke engine oil, which is specially formulated for our air- storage, if the machine is not under close supervision and cooled two stroke-engines.

  • Page 12: Fueling

    FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the WARNING! Taking the following precautions, fuel mixture.

  • Page 13: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping WARNING! When the engine is started with WARNING! The complete clutch cover and the choke in either the choke or start throttle shaft must be fitted before the machine is positions the cutting attachment will start to started, otherwise the clutch can come loose rotate immediately.

  • Page 14

    STARTING AND STOPPING Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.

  • Page 15: Working Techniques

    WORKING TECHNIQUES General working instructions 6 Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.

  • Page 16: Grass Trimming With A Trimmer Head

    WORKING TECHNIQUES Grass trimming with a trimmer head Sweeping • The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro. Trimming •...

  • Page 17: Maintenance

    MAINTENANCE Carburetor WARNING! If the idle speed cannot be adjusted so that the cutting attachment Your Husqvarna product has been designed and stops, contact your dealer/service manufactured to specifications that reduce harmful workshop. Do not use the machine until it emissions.

  • Page 18: High Speed Jet H

    MAINTENANCE High speed jet H The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust The high speed jet H affects the engine power, speed, gases are hot and can contain sparks, which may cause fire temperature and fuel consumption.

  • Page 19: Spark Plug

    Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through • A dirty air filter.

  • Page 20: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily Weekly Monthly Maintenance maintenance maintenance maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.

  • Page 21: Technical Data

    TECHNICAL DATA Technical data 223L Engine Cylinder displacement, cu.in/cm 1,50/24,5 Cylinder bore, inch/mm 1,34/34,0 Stroke, inch/mm 1,06/27 Idle speed, rpm 2700 Recommended max. fast idle speed, rpm 11000-11700 Speed of output shaft, rpm 8014 Max. engine output, acc. to ISO 8893, kW/ rpm 0,75/9000 Catalytic converter muffler...

  • Page 22: Federal And California Emissions Control Warranty Statement

    COVERAGE scheduled replacement, the part will be repaired or replaced by Husqvarna Forest & Garden at no cost. Any such part The emissions control system is warranted for two years. If repaired or replaced under warranty is warranted for the any emissions-related part on your equipment is defective, remainder of the period prior to the first scheduled...

  • Page 23

    EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non- exempted add-on or modified part.

  • Page 25

    6,0 m 10 cm 4" 3,05 m "Clic" 15 cm 6"...

  • Page 26

    T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...

  • Page 27

    8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...

  • Page 28

    4,25 m 4,25 m 15 cm 6" 15 cm 6"...

  • Page 36

    1151414-95 ´®z+SIQ¶5B¨ ´®z+SIQ¶5B¨ 2009-01-07...

Comments to this Manuals

Symbols: 0
Latest comments:
  • Brian Derise Jul 27, 2017 12:07:
    What is the fuel ratio for
    The 223l gas trimmer
  • Brian Derise Jul 27, 2017 12:00:
    What is the fuel mixture ratio for the
    223L gas trimmer