Download  Print this page

Craftsman 10 IN. TABLE SAW 315.22811 Owner's Manual: Rules For Safe Operation; Electrical

10 in. table saw.
Hide thumbs

Advertisement

RULES
FOR SAFE
OPERATION
(Continued)
DO NOT OVERREACH. Keep proper footing and
balance at all times.
SECURE WORK. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and frees both hands to operate tool.
USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
Use only a cord heavy er_oughto carry the
current your productwill draw. An undersized
cord will cause a drop in line voltage resulting in
loss of power and overheating. A wire gage size
(A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in
doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
AVOID ACCIDENTAL
STARTING.
Be sure
switch is off when plugging
in.
REMOVE WRENCHES AND ADJUSTING
KEYS. Get in the habit of checking - before
turning on tool - that hex keys and adjusting
wrenches are removed from tool.
CHECK DAMAGED PARTS. Before using the
tool again, check any damaged parts, including
guards, for proper operation and performance.
Check alignment of moving parts, binding of
moving parts, breakage of parts, saw stability,
mounting and any other conditionsthat may
affect its operation. A damaged part must be
properly repaired or replaced by a qualified
service technician at a Sears store or repair
center to avoid risk of personal injury.
USE ONLY CORRECT BLADES. Use the right
blade size, style and cutting speed for the
material and the type of cut. Blade teeth should
point down toward the front of the table.
USE RECOMMENDED ACCESSORIES. Using
improper accessories may risk injury.
USE ONLY SEARS REPLACEMENT PARTS.
All repairs, whether electrical or mechanical,
should be made by a qualified service technician
at a Sears store or repair center.
KEEP GUARDS
IN PLACE and in good working
order. This includes
the blade guard, riving knife,
and anti-kickback
pawls.
CHECK
DIRECTION
OF FEED. Feed work into
a blade or cutter against the direction
of rotation
of the blade or cutter only.
DISCONNECT
ALL TOOLS.
When not in use,
before servicing, or when changing attachments,
blades, bits, cutters, etc., all tools should be
disconnected from power supply.
DO NOT FORCE THE TOOL.
It will do the job
better and more safely at the rate for which it
was designed.
NEVER
LEAVE
TOOL RUNNING
UNAT-
TENDED.
TURN THE POWER
OFF. Do not
leave tool until it comes to a complete
stop.
BEFORE
DISCONNECTING
THE MOTOR;
unplug the saw from power supply.
WARNING:
When servicing,
use only identical
Craftsman
replacement
parts. Use of any other
parts may create a hazard or cause product
damage.
NEVER
USE THIS TOOL IN AN EXPLOSIVE
ATMOSPHERE.
Normal sparking
of the motor
could ignite fumes.
MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING
to see the work and that no obstruc-
tions will interfere with safe operation BEFORE
performing any work using this tool.
DO NOT USE TOOL IF SWITCH
DOES NOT
TURN IT ON AND OFF. Have defective
switches
replaced by a qualified service technician at a
Sears store or repair center
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces
such as pipes, radiators, ranges, refrigerator
enclosures.
GROUND
ALL TOOLS.
See Electrical page.
WEAR A DUST MASK to keep from inhaling fine
particles.
PROTECT
YOUR HEARING.
Wear hearing
protection during extended periods of operation.
DO NOT OPERATE
THIS TOOL WHILE UN-
DER THE INFLUENCE
OF DRUGS, ALCOHOL,
OR ANY MEDICATION.
STAY ALERT AND EXERCISE CONTROL.
Watch what you are doing and use common
sense. Do not operate tool when you are tired.
Do not rush.
AVOID AWKWARD
OPERATIONS
AND HAND
POSITIONS
where a sudden slip could cause
your hand to move into the blade. ALWAYS
make sure you have good balance.
ALWAYS
SUPPORT
LARGE WORK
PIECES
while cutting to minimize risk of blade pinching
and kickback.
Saw may slip, walk or slide while
cutting large or heavy boards,
5
CRRFTSMaW TABLESAW315.228110

Advertisement

   Related Manuals for Craftsman 10 IN. TABLE SAW 315.22811

This manual also for:

315.228110

Comments to this Manuals

Symbols: 0
Latest comments:
  • jim gibbons Apr 09, 2016 06:59:
    is there such a manual for the craftsman 10" table saw,i have looked everywhere to find manual and mitre gauge,anyo​ne got any info that can help me.